ls /

ELLO! BOOT0 is starting!
boot0 version : 2.3.7
reg_val=0x00000000
ss =0x00000000
[DRAM]ver 1.02 clk = 312
cpu 0 pmu 0
HELLO! BOOT0 is starting!
boot0 version : 2.3.7
reg_val=0x00000000
ss =0x00000000
[DRAM]ver 1.02 clk = 312
cpu 0 pmu 0
Found PMU:AXP221
ddr vol 1500mV
dram size =2048
card boot number = 0
card no is 0
sdcard 0 line count 0
[mmc]: SD/MMC Card: 4bit, capacity: 968MB
[mmc]: vendor: Man 0x00035344 Snr 0x00ba5beb
[mmc]: product: SD01G
[mmc]: revision: 8.0
sdcard 0 init ok
The size of Boot1 is 0x00048000.
Succeed in loading boot1 from sdmmc flash.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[ 0.209] boot1 version : 2.0.0
[ 0.214] script installed ok
[ 0.215] PMU: AXP221
[ 0.215] bat ratio = 100
[ 0.217] dcdc3 1260
[ 0.263] pll1 1008
[ 0.319] power finish
[ 0.324] dcdc1 3300
[ 0.324] dcdc2 1200
[ 0.324] dcdc4 1200
[ 0.325] dcdc5 1500
[ 0.328] flash init start
[ 0.582] [mmc]: init mmc pll6clk 600000000, clk 25000000, mclkbase 0x8151030b
[ 0.584] [mmc]: SD/MMC Card: 4bit, capacity: 968MB
[ 0.589] [mmc]: vendor: Man 0x00035344 Snr 0x00ba5beb
[ 0.594] [mmc]: product: SD01G
[ 0.598] [mmc]: revision: 8.0
[ 0.601] flash init finish
[ 0.638] fs init ok
[ 0.639] fattype FAT16
[ 0.639] fs mount ok
[ 0.646] dram_para_set start
[ 0.649] dram_para_set end
[ 0.649] type=1
[ 0.679] 0
[ 0.845] boot_disp.output_type=3
[ 0.845] boot_disp.output_mode=5
[ 0.847] boot_disp.auto_hpd=1
[ 0.850] hdmi open
[ 0.852] DRV_hdmi_set_display_mode,mode:5
[ 0.857] DRV_hdmi_open
[ 0.979] ERR: Parse_Pic_BMP failed
[ 0.979] key 0
[ 0.980] cant find rcvy value
[ 0.983] cant find fstbt value
[ 0.987] try to boot
[ 0.988] load kernel start
[ 1.024] load kernel successed
[ 1.024] start address = 0x4a000000
[ 3.066] jump to
[ 3.066] 0x4a000000

U-Boot 2011.09-rc1-00001-g8f3ca1c-dirty (Apr 23 2013 - 15:07:05) Allwinner Technology

CPU: SUNXI Family
Board: SUN6I
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
In: serial
Out: serial
Err: serial
MMC: block number 0x72a004 exceeds max(0x1e4600)
bootcmd set setargs_mmc
Hit any key to stop autoboot: 0
reading linux/uImage_dtb

2987715 bytes read
reading linux/uInitrd

2980928 bytes read

Booting kernel from Legacy Image at 46000000 ...

Image Name:

Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2987651 Bytes = 2.8 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK

Loading init Ramdisk from Legacy Image at 48000000 ...

Image Name: uInitrd
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 2980864 Bytes = 2.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
[ 9.888]

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.11.0-rc4-12838-gcc5d8a7-dirty (bamvor@linux-rd.site) (gcc version 4.8.1 20130401 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2013.04-20130417 - Linaro GCC 2013.04) ) #49 SMP Tue Aug 27 20:20:16 CST 2013
[ 0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Allwinner A1X (Device Tree), model: WITS A31 Colombus Evaluation Board
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] PERCPU: Embedded 5 pages/cpu @c1882000 s7104 r0 d13376 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522768
[ 0.000000] Kernel command line: earlyprintk console=ttyS0,115200
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2070932K/2097152K available (4368K kernel code, 202K rwdata, 928K rodata, 198K init, 243K bss, 26220K reserved, 1318912K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] .text : 0xc0008000 - 0xc05342dc (5297 kB)
[ 0.000000] .init : 0xc0535000 - 0xc0566bc0 ( 199 kB)
[ 0.000000] .data : 0xc0568000 - 0xc059a9a0 ( 203 kB)
[ 0.000000] .bss : 0xc059a9a0 - 0xc05d77d4 ( 244 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.005134] Calibrating delay loop... 2007.04 BogoMIPS (lpj=10035200)
[ 0.062977] pid_max: default: 32768 minimum: 301
[ 0.067813] Mount-cache hash table entries: 512
[ 0.073659] CPU: Testing write buffer coherency: ok
[ 0.078907] /cpus/cpu@0 missing clock-frequency property
[ 0.084324] /cpus/cpu@1 missing clock-frequency property
[ 0.089714] /cpus/cpu@2 missing clock-frequency property
[ 0.095112] /cpus/cpu@3 missing clock-frequency property
[ 0.100516] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.106810] Setting up static identity map for 0xc0426f48 - 0xc0426fa0
[ 0.114290] CPU1: failed to boot: -38
[ 0.118276] CPU2: failed to boot: -38
[ 0.122637] CPU3: failed to boot: -38
[ 0.126744] Brought up 1 CPUs
[ 0.129795] SMP: Total of 1 processors activated (2007.04 BogoMIPS).
[ 0.136862] CPU: All CPU(s) started in SVC mode.
[ 0.142141] devtmpfs: initialized
[ 0.149137] pinctrl core: initialized pinctrl subsystem
[ 0.154753] regulator-dummy: no parameters
[ 0.159148] NET: Registered protocol family 16
[ 0.163921] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.176527] bio: create slab at 0
[ 0.181495] SCSI subsystem initialized
[ 0.185961] usbcore: registered new interface driver usbfs
[ 0.191576] usbcore: registered new interface driver hub
[ 0.197533] usbcore: registered new device driver usb
[ 0.202865] pps_core: LinuxPPS API ver. 1 registered
[ 0.207907] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.218036] PTP clock support registered
[ 0.222429] EDAC MC: Ver: 3.0.0
[ 0.226638] Switched to clocksource timer
[ 0.237454] NET: Registered protocol family 2
[ 0.242387] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.249663] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.256288] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.262785] TCP: reno registered
[ 0.266102] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.272731] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.279414] NET: Registered protocol family 1
[ 0.284589] RPC: Registered named UNIX socket transport module.
[ 0.290610] RPC: Registered udp transport module.
[ 0.295851] RPC: Registered tcp transport module.
[ 0.301095] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.308393] Trying to unpack rootfs image as initramfs...
[ 0.342875] Freeing initrd memory: 2904K (c8001000 - c82d7000)
[ 0.350520] bounce pool size: 64 pages
[ 0.362182] NFS: Registering the id_resolver key type
[ 0.367937] Key type id_resolver registered
[ 0.372608] Key type id_legacy registered
[ 0.377337] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.385522] io scheduler noop registered
[ 0.389548] io scheduler deadline registered
[ 0.394041] io scheduler cfq registered (default)
[ 0.400662] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 0.449434] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.477391] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 32) is a U6_16550A
[ 0.484634] console [ttyS0] enabled, bootconsole disabled
[ 0.484634] console [ttyS0] enabled, bootconsole disabled
[ 0.496320] serial: Freescale lpuart driver
[ 0.500710] [drm] Initialized drm 1.1.0 20060810
[ 0.510998] brd: module loaded
[ 0.514523] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.521077] ehci-platform: EHCI generic platform driver
[ 0.526445] usbcore: registered new interface driver usb-storage
[ 0.532995] mousedev: PS/2 mouse device common for all mice
[ 0.538892] sdhci: Secure Digital Host Controller Interface driver
[ 0.545063] sdhci: Copyright(c) Pierre Ossman
[ 0.549437] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.555485] usbcore: registered new interface driver usbhid
[ 0.561064] usbhid: USB HID core driver
[ 0.565110] TCP: cubic registered
[ 0.568975] NET: Registered protocol family 10
[ 0.574082] sit: IPv6 over IPv4 tunneling driver
[ 0.579346] Key type dns_resolver registered
[ 0.583686] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 3
[ 0.591385] Registering SWP/SWPB emulation handler
[ 0.596828] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 0.603905] Freeing unused kernel memory: 196K (c0535000 - c0566000)
Starting logging: OK
Initializing random number generator... done.
Starting network...

Welcome to Buildroot
buildroot login: root

bin etc init linuxrc mnt proc run sys usr
dev home lib media opt root sbin tmp var

2013-08-27 20:34 335